Engineering Assignment Sample

Removing and Fitting Basic Light Vehicle Mechanical, Electrical, and Trim (MET) Components

Questions to be answered:

1.1 Identify the procedures involved in carrying out the systematic removal and fitting of basic light vehicle MET components to the standard required:

a. Bumpers
b. Headlamp units
c. Road wheels
d. Batteries

e. Bonnet and boot trim
f. Interior trim components
g. Exterior trim components

Answer:

Procedure of bumper removal:

Step 1: Place the vehicle on a lift and raise it. Remove wheel arch liner bolts.
Step 2: Remove the lower bolts which are fixing the bumper.
Step 3: Raise the vehicle down and remove the upper bolts attached to the bumper.
Step 4: In order to release the bumper from the side retainers, move the bumper slightly to one side. Disconnect the electrical connections.

Procedure of headlamp units removal:

Step 1: Remove grill.
Step 2: Remove front wheels.
Step 3: Remove plastic shields under front guards.
Step 4: Remove the bolts which attach the bumper to the guards.
Step 5: Remove bumper.
Step 6: Remove the bolts which are retaining the headlamp unit and which are exposed after the removal of bumper.
Step 7: Lift clip which is located underneath the point where the grill is bolted on.

Procedure of road wheel removal:

Step 1: Take off the hub cap and all decorative wheel trim.
Step 2: Slightly loosen the wheel nuts or bolts, than jack up the car.
Step 3: Remove the nuts.
Step 4: Before taking the wheels off, mark the wheel and studs.

Procedure of batteries removal:

Step 1: Turn off the vehicle’s engine.
Step 2: Open the hood and place a blanket or pad over the fender.
Step 3: Remove the cables from the battery terminals.
Step 4: Remove all devices which are holding the battery in place.
Step 5: Remove the battery.
Step 6: Clean the tray on which the battery was standing with a little baking soda dissolved in water.
Step 7: Place the new battery on the tray.
Step 8: Replace the devices that held the old battery in place.
Step 9: Replace the battery cables on the terminals in reverse order from which you removed them.
Step 10: Take the old battery to a recycling center that accepts batteries.

Procedure of bonnet and boot trim removal:

Step 1: Remove the wheel arch liners.
Step 2: Remove the front bumper.
Step 3: Remove the bonnet catch.
Step 4: Remove the battery.
Step 5: Unclip the power supply fuse support plate.
Step 6: Pull out the fuse board support.
Step 7: Place the new battery on the tray.
Step 8: Replace the devices that held the old battery in place.
Step 9: Replace the battery cables on the terminals in reverse order from which you removed them.
Step 10: Take the old battery to a recycling center that accepts batteries.

Procedure of interior trim components removal:

Step 1: Repease rear ash tray panel from rear console, disconnect multiplug from power socket, and remove panel.
Step 2: Remove oddments tray liner, raise cubby box lid, and remove cubby box.
Step 3: Remove 2 screws securing the rear of the console.
Step 4: Remove screw cover and remove 2 screws securing front of the console.
Step 5: Disconnect multiplugs from window lift switches and if fitted, rear window isolator switch.

Procedure of exterior trim components removal:

Step 1: Remove the door guide rail from the door.
Step 2: Remove the screws from the door.
Step 3: Remove the B-pillar molding.
Step 4: Remove the B-pillar cover.
Step 5: Remove the air extractor grill.
Step 6: Remove the front combination lamp.
Step 7: Remove the front wheel molding screws.
Step 8: Remove the front wheel molding from the body.
Step 9: Remove the rear wheel molding screws.
Step 10: Remove the rear wheel molding from the body.
Step 11: Remove the mud guard.
Step 12: Remove the side step mounting bolts.
Step 13: Remove the side step from the body.
Step 14: Open the tailgate.
Step 15: Remove the C-pillar cover with the screws.
Step 16: Remove the C-pillar cover.
Step 17: Remove the roof molding.

The presented engineering assignment sample was completed by one of our experts to present how projects of such type should be accomplished. It can help you to develop your own analytical skills and give you a hint how to cope with your project. You can’t use the sample, or its parts in your own aims, but luckily for you our experts can offer assignment help with engineering projects of any difficulty level. Don’t hesitate to contact us anytime needed.

Here is one more electrical engineering assignment example to analyze within your chosen discipline.